Sessions Index

S7 【S7】Advanced Interconnect Technologies

Oct. 20, 2026 10:10 AM - 12:10 PM

Room: 702, 7F, TaiNEX 2
Session chair: Takayuki Ohba, Institute of Science Tokyo / Yi-Chun Hu, NKUST

Crosstalk-Aware Channel Design in DDR5: Sensitivity Analysis of Via Length and Routing Topologies
發表編號:S7-1時間:10:10 - 10:25

Paper ID:AS0245
Speaker: Wei Jern Tan
Author List: Min Keen Tang, Wei Jern Tan, Mohd Zain Ahmad Syahmi

Bio:
Tan Wei Jern has been part of the semiconductor industry since 2012, working in both the Client and Server product segments. His focus has primarily been as Signal Integrity engineer in both platform design and customer product engineering. He has authored 11 papers and one patent.


Abstract:
This paper presents an electrical study of the impact of channel design affecting crosstalk in a DDR5 memory interface. The paper seeks to determine the limitations and tackle issues caused by complex design elements in combination with ever-increasing memory signal speeds. The study focuses on channel design by identifying the impact of signal-to-signal coupling through via length, channel routing schema and long serpentine signal routing. The correct implementation of the proposed methods yields improved margin performance in terms of eye height/Vref (mV) and eye width/delay (UI) margins. Of note, they maintain printed circuit board (PCB) design flexibility while enabling improved eye margins especially at higher memory data rates. A well-designed system can extend design limits while minimizing platform cost. In turn, a highly correlated simulation methodology capable of accurately predicting feasible routing solutions in pre-silicon evaluation of complex platform topologies is essential. This capability enables PCB designers to optimize hardware parameters such as layer count and board thickness. Consequently, it enables scalable and accelerated server hardware development for cost-efficient solutions, while maintaining system electrical integrity throughout the product lifecycle by enabling reliable signal integrity (SI) trade-off analysis and mitigating risks associated with suboptimal designs.
Keywords: Active Via Length, Channel Routing Schema, DDR5, Memory, Sensitivity Study, Serpentine Routing, Signal Integrity.


 
IMC Growth Kinetics and Microstructural Evolution of Au-Coated Ag Bonding Wires under High-Temperature Aging
發表編號:S7-2時間:10:25 - 10:40

Paper ID:TW0208
Speaker: Yi Jing Chen
Author List: Yung-Sheng Zou,Yi-Jing Chen,Kerguelen Mae Nodora, Min-Hua Chung, Chong-Leong Gan

Bio:
I hold a Master’s degree in Materials Science and Engineering from NCKU. I currently work as a Package Characterization Engineer at Micron Taiwan, specializing in wire interconnect development, material supplier and cross-functional teams collaboration, and failure analysis to drive material application in packaging.


Abstract:
The semiconductor packaging industry is increasingly seeking cost-effective alternatives to conventional gold (Au) bonding wires. Au-coated Ag (ACA) wire has emerged as a promising candidate; however, its interfacial reliability and intermetallic compound (IMC) evolution under high-temperature conditions require further investigation. This study evaluates the interfacial behavior of 0.6mil 99.0% Au and 0.7mil Au-coated Ag (ACA) wires under high-temperature storage (HTS) at 125 °C, 150 °C, and 175 °C using a die-attached stacked wire bond BGA package with forward wire bonding. Bonding performance, IMC growth kinetics, activation energy, and microstructural evolution were systematically analyzed using SEM/EDS and EBSD. ACA exhibited superior bonding performance, slower IMC growth, higher activation energy (1.174 eV), and no Kirkendall void formation compared to Au (0.8372 eV). These results demonstrate that ACA provides improved interfacial stability and reliability under prolonged thermal aging conditions.


 
Current Stressing on SAC/SnBi Hybrid Solder Stripe
發表編號:S7-3時間:10:40 - 10:55

Paper ID:TW0232
Speaker: Po-Kai Chang
Author List: Po-Kai Chang, Albert T. Wu

Bio:
I am a Ph.D. candidate at National Central University, focusing on advanced packaging techniques for electronic devices. My research specifically investigates electromigration in solder joints.


Abstract:
The growing number of I/O connections in advanced computing has raised current densities, making solder joints highly sensitive to electromigration (EM) damage. Following the ban on toxic lead, Sn-Ag-Cu (SAC) alloys became the standard choice. However, their high melting temperatures (>200°C) worsen thermal stress and assembly defects. To solve this, low-temperature solders (LTS) like Sn-Bi alloys are widely used. While Sn-Bi offers good initial strength, operational heat causes bismuth (Bi) to separate, making the joints brittle and lowering reliability. Hybrid solder joints combining SAC305 and Sn-Bi offer a balanced solution. This combination lowers overall thermal stress, while the softer SAC solder absorbs mechanical strain, reducing the brittleness caused by Bi separation. [1]
As electronic devices shrink, EM challenges in these joints become more critical. The directional movement of atoms during EM causes structural damage, typically appearing as solder being pushed out at the anode and voids forming at the cathode, eventually breaking the connection. [2] Under high current density, SAC resists EM better than Sn-Bi. In Sn-Bi systems, the separation of Sn and Bi is made much worse by the electron flow. [3] In hybrid solders, Bi shows a strong tendency to move in the direction of the electron flow. Furthermore, because the structure of a hybrid joint is asymmetrical, it results in different types of failures. [4] [5]While most research focuses on large-scale electrical testing, basic studies on how atoms diffuse and move between these two different solders are still lacking.
To address this research gap, our study investigates electromigration in hybrid solder strips prepared inside grooves etched on Si (001) wafers. Using standard semiconductor processing, we can precisely control the testing area to apply and reflow the two solders step by step, starting with the higher-melting SAC and followed by the lower-melting Sn-Bi. (Fig.1. &2.) Furthermore, dedicated copper pads are added to help the current flow smoothly into the test samples. This specific design reduces current crowding and prevents test probes from physically damaging the solder during the experiment. After applying a high current density over 10⁴ A/cm², we used microstructural observation and elemental analysis to clearly understand the different current-induced atom movements at the cathode, anode, and the SAC/SnBi interface. By tracking how these atoms migrate, we can better explain the fundamental failure mechanisms of hybrid solders.


 
Effect of Mn Diffusion from a Cu–Mn Seed on Cu–Cu Thermocompression Bonding
發表編號:S7-4時間:10:55 - 11:10

Paper ID:TW0126
Speaker: Kun-Yuan Zeng
Author List: Kun-Yuan Zeng , Shih-Kang Lin

Bio:
I am Prof. Shih-Kang Lin's student working on Cu/SiO2 hybrid bonding with the industry project


Abstract:
In recent years, driven by the explosive demand for artificial intelligence (AI) and high-bandwidth memory (HBM), hybrid bonding has become increasingly crucial in advanced packaging. Hybrid bonding with high-density interconnects is critical for advanced electronic packaging. However, a major challenge in Cu/SiO2 hybrid bonding is the high susceptibility of Cu to oxidation. During the chip-on-wafer (CoW) process, exposed Cu reacts with atmospheric oxygen to form copper oxides (CuxO). This oxide layer severely impedes Cu interdiffusion and degrades manufacturing yield. Consequently, numerous surface modification methods—such as self-assembled monolayers (SAMs), metal cap passivation, plasma activation, and wet chemical cleaning—have been developed to suppress the formation of the copper oxide layer.
To enhance bonding performance, we introduce a method utilizing a Cu-Mn alloy self-forming diffusion barrier, where Mn is doped into the Cu seed layer. During the bonding process, thermally induced diffusion drives Mn to migrate toward the bonding interface. Upon reaching the interface, Mn effectively reduces Cu2O, thereby eliminating its presence at the bonding interface.
Under low-temperature 200℃ and low-pressure 10 MPa bonding conditions, the Cu-Mn alloy self-forming barrier exhibits significantly higher bonding strength and a lower interfacial void ratio compared to conventional fine-grained Cu (FG-Cu). Notably, while Cu2O is observed along the bonding interface in FG-Cu samples, it is completely absent in the Cu-Mn samples. Instead, Mn oxides are formed as a result of the Mn-induced reduction of Cu2O. Because Mn oxides are electrically conductive—unlike the insulating copper oxides—their presence has a negligible impact on the electrical properties and does not severely degrade conductivity.
Furthermore, applying this identical process to coarse-grained Cu (CG-Cu) yields the same beneficial effects, successfully enhancing bonding strength, minimizing interfacial voids and eliminate the Cu oxide. From an industrial manufacturing perspective, doping Mn during the physical vapor deposition (PVD) of the Cu seed layer requires neither the acquisition of new capital equipment nor additional processing steps on separate tools, thereby offering a highly cost-effective solution for high-volume manufacturing.


 
Moving Boundary Modeling of β-In₃Sn Phase Dissolution Kinetics in Indalloy 227 Solder
發表編號:S7-5時間:11:10 - 11:25

Paper ID:TW0048
Speaker: Yu-Hsin Lin
Author List: Yu-Hsin Lin and C. Robert Kao

Bio:
Yu-Hsin Lin is a PhD student in Materials Science and Engineering at National Taiwan University, specializing in advanced electronic packaging and low-temperature solder alloys. Her research integrates experimental characterization with thermodynamic and kinetic simulations to address phase behavior and homogenization challenges.


Abstract:
Indalloy 227 (Sn-20In-2.8Ag, wt%) is a promising low temperature solder for next-generation electronic packaging, but reflow-induced segregation forms transient β-In₃Sn, whose low melting temperature may contribute to partial melting during downstream packaging processes. This study combines experiments and modeling to quantitatively investigate the sub-solidus dissolution and homogenization kinetics of β-In₃Sn within the γ-InSn₄ matrix.
To establish the thermodynamic boundary conditions of the initial state, Scheil solidification simulation was performed using Pandat software with the PanNob2025 database. The simulation predicted the formation of solute-rich β-In3Sn phase at 113°C. To simulate the physical shrinkage and dissolution kinetics of the β-In3Sn particles while avoiding the intensive computational overhead of mesh regeneration inherent to finite element analysis, a sharp-interface moving boundary model was implemented using custom Python code. Assuming a spherical geometry based on scanning electron microscope (SEM) observations, the instantaneous volume fraction was tracked as a function of the shrinking precipitate radius. The model dynamically updated the bulk matrix concentration at each time step, explicitly accounting for local solute enrichment as the interface migrated inward.
The numerical predictions of macroscopic phase fraction evolution were validated against experimental datasets obtained under isothermal holding at 75, 90, and 105 °C. The experimental data points were characterized using low-temperature differential scanning calorimetry (DSC) enthalpy, selected because in-situ microscopic are limited in providing continuous and quantitative phase evaluation within solid matrices at these low temperatures. Low temperature DSC resolves this limitation by measuring the phase transformation heat flow, which directly correlates to the transient phase fraction and yields statistically representative macroscopic kinetics. The calculated simulation curves show quantitative agreement with these enthalpy-derived experimental data points across all evaluated temperatures.
The model captured the gradual deceleration of dissolution characterized by the progressive deceleration of the interface velocity over time. The physical mechanism governing this deceleration is determined by solute redistribution within the finite matrix volume. As the phase transformation proceeds, indium atoms accumulate at the advancing front, leading to transient solute enrichment and localized saturation. Because the matrix volume is limited, this localized accumulation reduces the indium concentration gradient across the reaction front. The reduction in the concentration gradient decreases the chemical potential gradient and the thermodynamic driving force acting at the interphase boundary, resulting in the observed kinetic deceleration.
This study investigated β-In3Sn dissolution kinetics in Indalloy 227 using Pandat and a Python moving boundary model. Validated by low temperature DSC enthalpy data, the simulations predicted a non-linear kinetic retardation where the interface velocity decelerates over time. This deceleration is governed by transient indium enrichment and localized saturation within the finite matrix volume, which flattens the concentration gradient and diminishes the thermodynamic driving force at the interphase boundary.


 
Comparative Study of Electromigration Reliability between Sn-3Ag-0.5Cu and Sn-1In-0.5Cu Micro Joints
發表編號:S7-6時間:11:25 - 11:40

Paper ID:TW0223
Speaker: Zhao-Yu Yang
Author List: Zhao-Yu Yang, Kun-Jing Chen, Cheng-Yu Lee, Hung-Cheng Liu, and Cheng-En Ho

Bio:
1. Major in Chemical Engineering & Materials Science at Yuan Ze University. 2. Research expertise: Electromigration, Electrical Resistance.


Abstract:
In microelectronic packages, the formation of intermetallic compounds (IMCs) is necessary to ensure the metallurgical bonding of the solder/pad interface. Insufficient IMC growth accompanying by material defects may lead to poor interfacial bonding, threatening the overall reliability of microelectronic packages. To mitigate excessive IMC growth, minor alloying addition has been widely attempted to control interfacial reactions for years. Recently, minor indium (In) addition (2 wt.%) to tin (Sn) has been prone to suppresses the Cu3Sn growth as well as kirkendall’s voids formation during aging, thereby enhancing solder joint reliability. This study will further probe into the benefits of minor In addition on electromigration reliability of micro joints and the underlying mechanism related to the In effect on the electromigration behavior.


 


Organizer

 

 

Co-Organizer

                   

 

 

Partner

           

 

 

Co-hosting Event - TPCA Show 2026